CREAR TEST

TEST BORRADO, QUIZÁS LE INTERESE: avionica

COMENTARIOS	ESTADÍSTICAS	RÉCORDS

REALIZAR TEST

Título del Test: avionica Descripción: ARINC ASSEMBLY PART NUMBERS - 3520-0610-01 AND 3520-0610-03 Autor: rino OTROS TESTS DEL AUTOR Fecha de Creación: 17/10/2024 Categoría: Otros Número Preguntas: 25

COMPARTE EL TEST

Comentar

No hay ningún comentario sobre este test.

Temario:

What is the primary source of power for the Espresso Coffee Maker? "115 VAC, 400 HZ, three phase, wye- connected potential" Three 400 watt heaters Brew Cup assembly Steam operated milk frothing nozzle . How is the Espresso Coffee Maker mounted in the aircraft? "On a permanently installed base assembly" Held securely by a single release pin Through water inlet connector On the brew shelf . "What component is responsible for providing close dimensional controls for the Espresso Maker?" Brew Cup assembly Espresso Cup Brew handle Platen surface . Which part of the Espresso Coffee Maker serves as the brew chamber? Brew Cup assembly Espresso Cup Platen surface Brew handle . How is water heated in the Espresso Coffee Maker? "By three 400 watt heaters mounted at the rear" "By the steam operated milk frothing nozzle" By the solenoid By the pump . "What is the power requirement for operation of the Espresso Coffee Maker?" "115 VAC, 400 HZ, three phase, wye- connected potential" Brew Cup assembly Steam operated milk frothing nozzle Platen surface . "What must be in place to start a brew cycle in the Espresso Coffee Maker?" "Espresso Cup with the brew handle in the down position" Brew Cup assembly Espresso Pod Brew shelf . "What indicates that the water heater assembly is up to brew temperature?" READY light is illuminated "Espresso Cup with the brew handle in the down position" Brew Cup assembly Espresso Pod . When does milk frothing start in the automatic mode? "When the water heater assembly reaches the froth temperature" When the pump is activated When the brew cycle is completed When the brew handle is raised . How long does the brew cycle last? Between 18 to 24 seconds "Between 1 minute 30 seconds to 1 minute 50 seconds" Between 143 and 157 psig Between 100 to 150 psig . How is milk frothing initiated in the manual mode? "By pressing and holding the FROTH button" By pressing the BREW switch By lowering the brew handle By pressing the ON/OFF switch . "What safety feature prevents operation of the Espresso Coffee Maker under certain conditions?" Control circuits Thermal Switches Pressure relief valves Megohmmeter . How is the Espresso Coffee Maker pressurized during aircraft pressure testing? Through water inlet connector to 100 psig (689.4 kPag) Through solenoid (S9) to fill the tank assembly Through manifold pressure relief valve line to 150 psig (1034.2 kPag) Through Brew Cup assembly . "What is tested by applying a voltage of 500 VDC during the dielectric test?" Insulation resistance Leakage current flow Temperature regulation circuit The housing . "Which component is checked by connecting an ohmmeter from P1-G to ground stud SG2?" Relay (K1) Brew handle Brew shelf Solenoid (S9) . What is tested during the proof pressure test? Pressure relief valve Heater (HR1-HR4) Water inlet connector Brew Cup assembly . "When does the relay cut off power to all three heaters during the relay check?" "When ON/OFF switch is in the ON position" When the brew cycle is completed "When the water heater assembly reaches the froth temperature" When the pump is activated . What indicates that the Espresso Coffee Maker is ready for brewing? READY indicator FROTH light BREW light ON/OFF switch . "How is the time for the brew cycle monitored during the Espresso test?" With a stopwatch By observing amperage draw By pressing the FROTH button By observing the READY lamp . What is the primary purpose of the procedure section in the manual? To provide testing and fault isolation procedures To describe the operation of the Espresso Coffee Maker To list the safety features To describe the mounting of the Espresso Coffee Maker in the aircraft . What material is used for the construction of the Beverage Maker? Cast aluminum-magnesium-titanium Stainless steel Plastic Copper . What component heats the water in the Beverage Maker? "Three 900 watt immersion type heaters mounted in the bottom of the tank" Brew handle Platen heater Server cavity . What is the purpose of the brew chamber in the Beverage Maker? "To retain grounds in the event of a torn or broken pillow pack" To hold the coffee or tea bags To heat a server full of hot water "To maintain liquid temperature between 165° F to 195° F" . "What does the LOW WATER indicator light indicate in the Beverage Maker?" Low water level in the tank High water temperature Full server Brew cycle completion . How is the brew cycle reset if it is interrupted in the Beverage Maker? "By pressing the POWER button OFF and ON again" By pressing the BREW button again By lifting the brew handle By removing the brew cup .

Denunciar Test