PRACTICA A

The customer is performing an initial setup of an HPE Alletra 6000 system. Which user interface can you use to define initiator when configuring an HPE Alletra 6000 system?. Command ""Addinitiator"" in Nimble/Alletra CLI. Web-based Alletra UI. Command ""Addinitiator"" in Host OS. Graphical VNC connection to Alletra system.

How does HPE GreenLake for Block Storage perform VV and LD ownership?. VV LDs shared based on system parameter ""enh_ownership"". VV LDs are shared across all nodes. VV LDs are owned by a single node. VV LDs are adaptively shared based on the array config".

"Your customer is running out of space on thir HPE StoreOnce while it appears ther are barely any backups present. Which of the following options could resolve this?". Trigger space reclamation via HPE StoreOnce local UI. Configure backup application to run unmap when backup is expired. Ensure HPE StoreOnce blackout windows allow housekeeping to run. Run degragmentation via HPE StoreOnce CLI.

What is the maximum number of ISLs that can be combined to enhace the performace and avaliability of switch connections in a B-Series trunk group?. 12. 4. 6. 8.

Which Veeam feature allows you to automate validation of the backed up data?. Explorer. SureBackup. DataLabs. On-Demand Sandbox.

"Your customer would like to implement a data protection technology that will offer the lowest possible RPO and will protect from entire array failure. Which technology should the be used?". Disk-based backup. Synchronous replication. Asychronous replication. Snapshots.

What is the maximum number of host-facing PCIe expansion slots available in a HPE Alletra 6030 system?. 2. 4. 6. 3.

Select the correct description of RTO. A set of policies, tools, and procedures to enable the recovery or continuation of vital technology infrastructure. Maximum elapsed time allowed to complete the recovery of application processing. Maximum amount of acceptable data loss in the event a disaster occurs. A property that enables a system to continue operating properly.

"Your customer would like to improve the security of their backups with HPE StoreOnce data-at-rest encryption. Which statement is tru for this feature?". It is a hardware assisted feature. It is only supported by Catalyst Store. It can be tested for free as a part of a demo license. It must be enable during creation of the backup device.

Which of the following actions should be performed if your customer cannot deploy vVols on their HPE GreenLake for Block Storage?. Order a RAM upgrade pack. Update the OS to release 3 (10.3) or higuer. Acquire a VMware Site LTU. Run the ""setsys vVol 1"" command on the array CLI.

"In discussion with a customer, you are asked about a solution that would support 100G iSCSI connectivity. To which product is this topic related to?". Alletra MP 16-core. Alletra 9060 y 9080. Alletra 6030. MSA 2062.

"A solution achitect is sizing the required capacity for an HPE Alletra 9000. Customer requirements include: - 100TB base valumes - 168 snapshots a week - 15% daily change rate How much capacity is needed for snapshots after one week?". 700TB. 15TB. 105TB. 1680TB.

How many alerts can be configured when setting up performance alerts on HPE Alletra 9000?. 64. 48. 157. 32.

Which HPE storage family should you recommend for a hybrid array, utilizing both SSD and HDD media, supporting 512 TB of raw storage and centralized cloud-based management?. HPE Alletra 6000. HPE GreenLake for Block. HPE Alletra 5000. HPE XP8.

Which product can you recommend as a SAN component for refreshing an iSCSI-based SAN that supports wire speed Ethernet, comes in a 1U fabric form with two independent switches, and supports 100GbE. HPE M-series SN2010M. HPE B-series SN6500B. HPE M-series SN3700cM. HPE B-series SN6700B.

What data access protocol does the HPE Alletra dHCI solution use between storage and compute layers?. NVMe-oF. NFS. iSCSI. FC.

Which of the following statements describes the encryption capabilities of the HPE Alletra 5000?. It is hardware based and requires DAR capable disks. It only supports data at rest encryption. It supports data in flight encryption for synchronous replication. It supports data in fligh encryption for async replication.

"Which type of host identification is used in an iSCSI-based SAN? Nota cultural: iSCSI uses the iSCSI Qualified Name (IQN) and Extended Unique Identifier (EUI)". DCB. WWPN. IQN. WWNN.

How can the capacity of an HPE StoreOnce 3620 be expanded?. By increasing internal drive capacity. By adding a 5660 in slave mode. By adding disk enclosures. By adding a 3620 in slave mode.

"Which HPE system can benefit from storage class memory card? Abreviacion de ""storage class memory card"" = SCM". HPE Alletra 5010H. HPE Alletra 6000. HPE Alletra 5030. HPE StoreOnce.

Which SSD controller component is responsable for wear leveling?. Processor. NAND memory controller. SATA interface chip. DRAM.

Which of the following components will need to be updated manually when performing an intelligent (One-Click) Update on Alletra dHCI?. VMware vCenter. VMware ESXi. HPE Storage Connection Manager. Array OS.

What is the maximum set size value that can be manually set for and HPE GreenLake for Block Storage system equipped with two enclosures/cages, considering a high availability (HA) level for a drive/disk?. 10+2. 8+2. 6+2. 5+1.

Which statement is true regarding the connection of extra drive enclosures to the HPE Alletra 9000 storage array with and HPE Alletra 9000 NVMe-oF 100 GbE 2-port host bus adapter?. It must be installed on every node in the second HBA slot (slot 4). It offers a lower speed than built-in expansion ports and should be used with slower disks. Alternatively, it can be used for host connectivity. It can only be used if the two 100 GbE built-in ports are already populated.

"Your customer has asked you to add new HPE Alletra 9000 array to HPE SSMC. What should be your next step? Por lo que leo el Alletra 9000 no se soporta en el StoreServ Management Console (SSMC), sólo por la UI y por el Data Service Cloud Console (DSCC), solo que no encuentro como justificar la respuesta". Ensure WEB API is enable, then add system via SSMC Admin Console. Order HPE SSMC LTU to unlock the UI. Tell them the HPE Alletra 9000 does not support SSMC. Run ""setsys ssmc 1"" command to initialize the feature.

What information should be collected for creating a proper host entry within Data Ops Manager when using an HPE Alletra MP solution?. Port World Wide Name. Data protection policy. LUN ID. HBA vendor.

"You are required to create a sizing based on an existing VMware legacy configuration for a customer solution for a new HPE SimpliVity setup. Which HPE tool can you utilize to create the required output?". Ninja Stars. CloudPhysics. OCA. Ninja Online.

Which of the following statements is true regarding your customer´s support status when moving from an HPE StoreOnce backup appliance to HPE GreenLake Backup and Recovey?. The HPE StoreOnce appliance connectivity is currently FC-only. The HPE StoreOnce appliance is currently not supported. The HPE StoreOnce appliance can be only used as on-Premises Protection Store copy target. The HPE StoreOnce appliance can be shared with other backup applications.

"Your customer has very low deduplications ration on their Linux VMs farm which is hosted on a HPE Alletra 9000. Which filesystem type could cause this?". EXT 3. EXT 4. Btrfs. XFS.

For optimizing HPE StoreOnce Catalys Store settings by enabling fixed-block chunking. Which backup solutions is this setting applicable to?. HPE Data Protector. Veeam B&R. HPE SimpliVity backup. CommVault.

Which statement regarding the deduplication process on HPE StoreOnce is a true?. It is only available for Catalyst Store. It requires and extra license. It can be disable at any time. It is applied on a per-VTL/NAS/Catalyst Store basis.

What is the maximum number of 2140 4U All-Flash Array expansion shelves supported by the HPE Alletra 6030 storage?. 2. 3. 1. 4.

Which SAN topology will result in E Port type at the SAN switch?. Routed fabric. Point-to-point. Meshed fabric. Arbitrated loop.

"Your customer is interested in the HPE GreenLake for Block Storage Mission-critical service. Which storage array hardware does this service use?". HPE Alletra dHCI. HPE XP8. HPE Alletra 9000. HPE Alletra 6000.

"A solution achitect is sizing the required capacity for an HPE Alletra 9000. Customer requirements include: - 200TB base volumes - Regular snapshots being taken every hour with one-week retention - 10% daily change rate How much capacity is needed for snapshots after one week?". 200TB. 20TB. 140TB. 480TB.

How does HPE GreenLake for Block Storage perform write operations caching?. Data is cached on DFC-hosted SSDs. Data is buffered in NVDIMM. Data is stored in supercapacitor-protected RAM. Data goes directly to space based on NVMe.

Which HPE storage array offers the ability to survive any three disks falling at the same time?. HPE Alletra 9000. HPE GreenLake for Block Storage MP. HPE XP. HPE Alletra 5000.

"Your customer currently uses a VMware-based Veeam backup proxy. The would like to perform a direct backup from their FC-connected Alletra 9000 array. What could be the reason for the backup falling back to network mode?". VM-based backup proxy has not enogh RAM and more must be assingned in VM properties. Direct backup from an HPE Alletra 9000 array requires an Advance Backup LTU. Direct backup from a FC-connected array is only available on physical server-based backup proxy. HPE Alletra 9000 storage array WS API connection timeout value must be increased.

You are required to create a configuration including the sizing and performance values for a customer solution for Alletra MP. Which HPE tool can you utilize to create the required output?. Ninja Stars. Ninja Online. SAF. OCA.

Which cloud/object-storage provider can be used to deploy HPE StoreOnce VSA?. Scality ARTESCA. Microsoft Azure. Amazon AWS. Scality RING.

Which low-latency protocol should you recommend for a local flash-based drive connected directly to PCIe, eliminating the performance penalty of an array controller?. SATA. NVMe. SAS. FATA.

Which backup target will achieve protection from ransomware attacks by decreasing the oportunity for backups to become encrypted?. NAS backup repository. Catalys Store backup repository. DAS backup repository. Exported RW storage snapshot.

You are required to create a configuration for pricing for a customer solution for a primary storage use case. Which HPE tool can you utilize to create the required output?. SAF. OCA. CloudPhysics. Ninja Stars.

The customer uses an HPE Alletra 6000 system and wants to create snapshots of selected volumes automatically at a specific schedule. Which part of the web-based UI will you recommend for this operation?. Hardware. Data Protection. Data Access. Performance Policy.

Recommend a software stack for changing a backup platform that includes pay-per-use, supports backup of virtualized workloads provided by HPE GreenLake, offers low RPO in minutes, supports HPE Alletra 9000, and integrates with DSCC. Recovery Manager Central. Veeam Backup and Recovery. HPE GreenLake Backup and Recovery. Zerto.

The customer is deploying a new HPE Alletra dHCI Storage. Select a correct statement related to HPE Storage Setup Manager: HPE SSM requires connectivity to HPE GreenLake platform. The setup process includes setting up an IP addressing. vCenter connectivity configuration is a mandatory step in the setup process in SSM. A new user account must be created.

What are the benefits of the Persistent Cache feature?. Automatic write cache remirroring in case of partner-node failure. Ability of cache to retain content without power. Internal validation of checksum for data kept. Ability to relocate a cache module to a new array to keep private keys.

Which UI should be recommended to identify eleveted latency and the root causes across host, storage, or SANs on an HPE Alletra 9000 storage array?. HPE InfoSight. HPE Data Services Cloud Console. HPE Alletra 9000 UI. HPE Alletra 9000 CLI.

A solution achitectt is explaining RBAC concepts behind the HPE GreenLake Platform. How can the customer manage users in HPE GreenLake Platform after creating new company account?. The creator of the company account must create another account with Account Administrator role. HPE Support must be used to create an administrator account for the organization. The creator of the company account is automatically assigned to the Account Administrator role for the organization. Single company can only have one account.

The customer is using HPE GreenLake for Backup & Recovery. Which steps are necessary to define a Protection Policy in HPE GreenLake Data Services console?. Create iSCSI tunnel between array and d2d appliance. Define source and destination array. Define Hyper-V or vCenter server and snapshot frequency. Define the name of policy, scheduling and destination.

Your customer would like you to prepare an upgrade plan that includes adding extra disk to their HPE GreenLake for Block Storage array to boost performance optimization. What would be the optimal minimum upgrade?. 1 SSD per system. 1 SSD per enclosure. 2 SSDs per enclosure. 2 SSDs per system.

Which statement regarding controller nodes on the HPE Alletra 9000 series is true?. Node 0 + 1 are in the low 2U positions and use the bottom 24 drives. All four nodes are required for HPE Alletra 9080 to operate. HPE Alletra 9060 supports up to two controller nodes. Each contorller node can connect to all 48 drives in the enclosure.

Recommend a software stack for a backup platform change that supports on-premise deployment, direct backups from Linux and Windows systems, NAS protocol support for the backup repository, and integration with HPE StoreOnce. Recovery Manager Central. Zerto. HPE GreenLake Backup and Recovery. Veeam Backup and Recovery.

Based on the customer requirements for hybrid storage solution with fibre channel connectivity. What would you need to consider when proposing HPE Alletra?. Alletra 5000 flash to disk ratio would need to be sufficient for the workload. Alletra 6030 models and above is required for a hybrid with FC connectivity. Alletra 6000 flash to tier disk would need to be sufficient for the workload. Alletra 5030 models and above is required for a hybrid with FC connectivity.

Which low-cost storage technology is suitable for long-term archiving?. RAM. NVMe flash storage. Persistent Memory. Tape.

You have configured a performance alert with the following command: "createsralertcrlt port writeiops>10000,sumwrite_iops>5000 alert" Which of the following options will trigger the alert?. if an arrS and if the sum ay port has received more than 10 000 write IOPof all write IOPS for all ports exceeds 50 000. f an array port has received more than 10 000 write IOPS or if the sum of all write IOPS for all ports exceed 50 000. if a host port has transfered more than 10 000 write IOPS and if the sum of all host write IOPS for all ports of that host exceed 50 000. if a host port has transfered more than 10 000 write IOPS or if the sum of all host write IOPS for all ports of that host exceed 5000.

You´re starting to design a ToR network for a customer that will use it for iSCSI or NVMe-oF-TCP storage. The disign requires a switch with a maximum of 48 ports and 10/25GB speed. What is the best recommended switch for this scenario?. SN2700M. SN3700cM. SN2410M. SN2410bM.

What HPE Alletra 9000 CLI command allows you tu display real-time statistics on exported volumes including roundtrip time of an IO as seen by the system?. srstatvv. statvlun. statvv. srstatvlun.

How can an IT administrator access the HPE Alletra dHCI Stack Manager for managing their HPE Alletra dHCI solution?. Via HPE Alletra 5000/6000 CLI. Via HTML5 VMware vSphere client. From Alletra 9000 on-array Management UI. From fabric manager.

When adding a first 2140 4U All-Flash expansion shelf into your customer´s HPE Alletra 6000 array, what considerations should be taken?. The array model must be at least Alletra 6030 running array OS 6.1.2.0 and later. x100 GbE 2-port OCP Mezzanine adapter kit must be ordered along the expansion shelf. HPE Services rebalancing service must be ordered along the expansion shelf. Expansion shelf must be populated with same disk capacity as the head shel.